Call Today

 

Every person has got their personal ideas when it comes to A Step-by-Step Guide to Installing a Bathtub.

Setting up a bathtub isn't exactly rocket science, but it does call for strong plumbing, carpentry, and also often, tiling abilities. Changing an old bath tub with a new one is also a moderately challenging job. If the old bathtub is conveniently available, the project can relocate easily; if you need to open up a wall to get rid of the old tub and also place the brand-new tub, the job is a lot harder. In either situation, the task is within a residence handyman's skills, although you will certainly require a helper to move out the old bathtub as well as set in the brand-new one. Make sure you have actually certified yourself for the work and also are comfortable attempting it. Rather than employing a contractor to take over a halfway-completed project, it is far better to consider utilizing one before you start. Opportunities are you might require a professional plumber to make tube connections.
This write-up will aid you install a brand-new bathtub in your washroom if you have already acquired a brand-new bathtub and also don't need to transform the setup of your previous water pipelines.
Your tools and also material checklist should make up the following:

 

• New Bathtub


• Hammer


• Pipe Wrenches


• Prybar


• Shatterproof glass


• Degree


• Pliers


• Flexible Wrench


• Putty Knife


• Screwdriver


• Cold Blade


• Measuring tape


• Pipeline Caps


 

Removing Old Touches

If you need to replace old faucets with brand-new ones as a part of your installment, then the first thing you ought to do is disconnect the water. After doing so, turn on the faucets to drain pipes any type of water continuing to be in the system. The process of eliminating the existing taps can be fairly bothersome because of the limited gain access to that is often the case.
Use a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipes to the faucets. Have a towel ready for the remaining water that will certainly originate from the pipes. When the supply pipelines have actually been removed, make use of the same device to loosen up the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from transforming during this procedure. As soon as the taps have been eliminated, the holes in the bath/basin will need to be cleansed of any old sealing compound.
Before going on to fit the new faucets, compare the pipe links on the old faucets to the new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the new taps to fit.

 

 

Fitting New Taps

If the tails of the brand-new faucets are plastic, then you will certainly need a plastic connector to prevent damage to the string. One end of the adapter fits on the plastic tail of the faucet and also the other end provides a connection to the current supply pipelines.
If you require to fit a monobloc, then you will require minimizing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next, position the tap in the placing opening in the bath/basin making certain that the washers remain in place between the faucet and also the sink. Secure the faucet in position with the maker given backnut. Once the tap is safely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with typical faucet connectors. The former type must be connected to the faucet finishes first, tightening only by hand. The supply pipes can later on be connected to the other end. Tighten both ends with a spanner after both ends have been attached.

 

 

Mounting the Bath tub

Utilizing both wooden boards under its feet, position the tub in the needed setting. The wood boards are helpful in evenly spreading the weight of the bathtub over the location of the boards rather than focusing all the weight onto 4 little points.
The next objective is to guarantee that the tub is leveled all round. This can be accomplished by inspecting the level as well as readjusting the feet on the tub till the spirit level reads level.
To install faucets, fit the bottom of the furthest flexible tap port to the proper supply pipe by making a compression join; after that do the same for the other faucet.
Turn on the water system and examine all joints as well as brand-new pipework for leaks and tighten them if essential. Load the bathtub and also check the overflow outlet and also the regular outlet for leaks.
Finally, deal with the bathroom paneling as described in the maker's instruction manual. Tiling as well as securing around the bathtub ought to wait up until the bathtub has been utilized at least when as this will certainly resolve it into its final setting.

 

 

Getting ready for the Installment

First of all, the supporting structure provided with the bathroom must be fitted (if required) according to the producer's directions. Next off, fit the taps or mixer to the tub. When suitable the tap block, it is important to make certain that if the faucet comes with a plastic washing machine, it is fitted between the bath and the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the taps unit to avoid pressure on the bath tub.
Fit the versatile tap ports to the bottom of the two taps using 2 nuts as well as olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet through the hole in the bath. Use the nut provided by the producer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bathroom. Ensure you utilize all of the supplied washing machines.
Connect the catch to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom need to now be ready to be suited its final setting.

 

 

Tiling Around the Bath tub

In the location where the bath fulfills the ceramic tile, it is needed to seal the joins with a silicone rubber caulking. This is necessary as the installation can move sufficient to crack a rigid seal, causing the water to permeate the wall in between the bath and also the tiling, causing complications with dampness and possible leaks to the ceiling listed below.
You can choose from a variety of coloured sealers to assimilate your components and fittings. They are offered in tubes and cartridges, and can securing spaces up to a size of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with twists of soaked newspaper or soft rope. Remember to constantly fill the tub with water before sealing, to allow for the activity experienced when the tub is in usage. The sealant can split relatively very early if you do not think about this movement prior to sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise quickly available on the market. It is advisable to fit the ceramic tiles utilizing water-resistant or water-proof adhesive and also cement.

 

Bathtub Installation

 

How Important Is A Bathtub To Your Home?

 

High-quality baths, showers, and other bathroom updates are necessary when considering a smart investment in your home. It’s a room that you go to every day and one that is constantly being used by guests.The bathroom is one of the top trafficked rooms in a home and also one of the most valuable in terms of home resale.

 

Install Piping Before Tub

 

You will be using your existing drain and waste vent system, but pipes required include the hot and cold water supply lines and a pipe leading to a shower head. A mixing valve and shower head are also needed. Air chambers may be required.

 

Position the Tub

 

Lower the tub into place so that the continuous flange fits against the wall studs and rests on 1’x4' or 2’x4' supports. Anchor the tub to the enclosure with nails or screws inserted through the flanges into the studs.

NOTE: Remember, bathtubs and shower stalls may require support framing. A bathtub filled with water is extremely heavy, so check building codes and framing support before installing the tub.

 

Assemble Drain Connections

 

Assemble the bathtub drain connections by connecting the tub overflow with the tub drain above the trap, not beyond it. The trap will have a compression fitting that screws over the arm of the overflow assembly.

 

Place a Pipe For the Shower Head

 

First, locate a brass female threaded winged fitting and attach it to a framing support via a screw or a nail. Then run a pipe up the wall for the shower head. Sweat or solder the other side of the brass fitting to the top of the pipe.

 

Attaching Hot and Cold Water Lines

 

Attach your water lines for both hot and cold by sweating these directly into the hot and cold ports of the mixing valve. The mixing valve will be how water enters the tub’s system, not by the pipes themselves.

 

Install the Spout

 

Extend a piece of 1/2 inch pipe, or whichever length is specified in the manufacturer’s instructions, for the tub spout. Sweat on a male threaded fitting at the end of the pipe or use a brass nipple of the proper length and a 1/2 inch cap.

NOTE: At this point you should have your rough-in plumbing work inspected before proceeding further.

 

Check For Leaks

 

Restore the water pressure and check the drain connection and the supply pipes for any sign of leaking.

 

estore the Bathroom Wall

 

Replace the wall with moisture-resistant drywall as a base for your wall covering. Seal the joints between the wall and your new tub with silicone caulk as protection against water seepage.

https://www.berkeys.com/2016/12/02/bathtub-installation-dallas/

 

We hope you liked our piece on Installing A Bathtub. Thanks a ton for taking the time to read our content. Do you know about somebody else who is truly interested in the topic? Please feel free to share it. Thank you for your time spent reading it.

We've got this!